Avrdude
From Attie's Wiki
(Difference between revisions)
m |
|||
Line 1: | Line 1: | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
For detailed info: | For detailed info: | ||
− | + | <pre> | |
$ man avrdude | $ man avrdude | ||
− | + | </pre> | |
− | + | <h2>See Also</h2> | |
− | [[avr-gcc]] | + | [[avr-gcc]]<br> |
− | [[bus pirate]] | + | [[bus pirate]]<br> |
− | [[atmega328p]] | + | [[atmega328p]]<br> |
http://doswa.com/blog/2010/08/24/avrdude-5-10-with-ftdi-bitbang/ | http://doswa.com/blog/2010/08/24/avrdude-5-10-with-ftdi-bitbang/ | ||
− | + | <h2>Useful Lines</h2> | |
− | + | <h3>For using the Arduino bootloader</h3> | |
− | + | <pre> | |
$ avrdude -c stk500v1 -P /dev/ttyUSB1 -p m328p -y -U flash:w:main.hex | $ avrdude -c stk500v1 -P /dev/ttyUSB1 -p m328p -y -U flash:w:main.hex | ||
$ avrdude -c stk500v1 -P /dev/ttyUSB1 -p m328p -y -U flash:r:main.hex:i | $ avrdude -c stk500v1 -P /dev/ttyUSB1 -p m328p -y -U flash:r:main.hex:i | ||
− | + | </pre> | |
− | + | <h3>For using the buspirate</h3> | |
− | + | <pre> | |
$ avrdude -c buspirate -P /dev/ttyUSB1 -p m328p -y -U flash:w:main.hex | $ avrdude -c buspirate -P /dev/ttyUSB1 -p m328p -y -U flash:w:main.hex | ||
$ avrdude -c buspirate -P /dev/ttyUSB1 -p m328p -y -U flash:r:main.hex:i | $ avrdude -c buspirate -P /dev/ttyUSB1 -p m328p -y -U flash:r:main.hex:i | ||
− | + | </pre> | |
− | + | <h2>Parameters</h2> | |
− | Parameters marked with a | + | Parameters marked with a <span style="color:red">*</span> are required. |
− | + | <h3><span style="color:red">*</span> Programmer Type</h3> | |
− | * | + | * <code>-c buspirate</code> - for use with the buspirate |
− | * | + | * <code>-c stk500v1</code> - for use with the Arduino bootloader |
* other (see the man page) | * other (see the man page) | ||
− | + | <h3><span style="color:red">*</span> Programmer Port</h3> | |
− | * | + | * <code>-P /dev/ttyUSB1</code> - the most likely for my systems |
− | + | <h3><span style="color:red">*</span> Part Identifier</h3> | |
− | * | + | * <code>-p m168</code> - for use with an ATMega168 |
− | * | + | * <code>-p m328p</code> - for use with an ATMega328p |
− | * | + | * <code>-p m1280</code> - for use with an ATMega1280 |
− | + | <h3><span style="color:red">*</span> Burn Counter</h3> | |
Not technically required, but a good idea. The burn counter is stored in the last 4 bytes of eeprom | Not technically required, but a good idea. The burn counter is stored in the last 4 bytes of eeprom | ||
− | * | + | * <code>-y</code> - to increment the burn counter each burn |
− | * | + | * <code>-Y <i>value</i></code> - to initialise the burn counter |
− | + | <h3>Baud Rate</h3> | |
− | Required for | + | Required for <code>stk500v1</code><br> |
− | * | + | * <code>-b 57600</code> - for most of mine |
− | + | <h3>Terminal Mode</h3> | |
− | * | + | * <code>-t</code> - see [[#terminal_mode]] for mode |
− | + | <h3>Memory Access</h3> | |
There are others, but these are the most common | There are others, but these are the most common | ||
− | * | + | * <code>-U flash:<i>operation</i>:<i>filename</i>[:<i>format</i>]</code> - where the firmware lives |
− | * | + | * <code>-U eeprom:<i>operation</i>:<i>filename</i>[:<i>format</i>]</code> - non-volatile memory |
− | * | + | * <code>-U lfuse:<i>operation</i>:<i>filename</i>[:<i>format</i>]</code> - low fuse byte |
− | * | + | * <code>-U hfuse:<i>operation</i>:<i>filename</i>[:<i>format</i>]</code> - high fuse byte |
− | * | + | * <code>-U efuse:<i>operation</i>:<i>filename</i>[:<i>format</i>]</code> - extended fuse byte |
− | + | <code><i>operation</i></code> can be: | |
− | * | + | * <code>r</code> - read |
− | * | + | * <code>w</code> - write |
− | * | + | * <code>v</code> - verify |
− | + | <code><i>filename</i></code> points to the file to use | |
− | + | <code><i>format</i></code> can be: | |
− | * | + | * <code>a</code> or omitted - for auto-detection |
− | * | + | * <code>i</code> - Intel Hex (output from obj-dump) |
− | * | + | * <code>r</code> - Raw binary |
* other (see the man page) | * other (see the man page) | ||
− | + | <h2 id="terminal_mode">Terminal Mode Commands</h2> | |
− | + | <h3><code>dump</code></h3> | |
− | * | + | * <code>dump <i>memtype</i> <i>address</i> <i>nBytes</i></code> - dump <i>nBytes</i> from <i>address</i> in hex and ASCII |
− | * | + | * <code>dump</code> - continue for another <i>nBytes</i> |
− | + | <h3><code>write</code></h3> | |
− | * | + | * <code>write <i>memtype</i> <i>address</i> <i>byte1</i> <i>...</i> <i>byteN</i></code> - write to memory by hand, currently doesn't work with flash :( |
− | + | <h3><code>parm</code></h3> | |
− | * | + | * <code>part</code> - display information on the connected part |
Revision as of 23:39, 18 December 2010
For detailed info:
$ man avrdude
Contents |
See Also
avr-gcc
bus pirate
atmega328p
http://doswa.com/blog/2010/08/24/avrdude-5-10-with-ftdi-bitbang/
Useful Lines
For using the Arduino bootloader
$ avrdude -c stk500v1 -P /dev/ttyUSB1 -p m328p -y -U flash:w:main.hex $ avrdude -c stk500v1 -P /dev/ttyUSB1 -p m328p -y -U flash:r:main.hex:i
For using the buspirate
$ avrdude -c buspirate -P /dev/ttyUSB1 -p m328p -y -U flash:w:main.hex $ avrdude -c buspirate -P /dev/ttyUSB1 -p m328p -y -U flash:r:main.hex:i
Parameters
Parameters marked with a * are required.
* Programmer Type
-
-c buspirate
- for use with the buspirate -
-c stk500v1
- for use with the Arduino bootloader - other (see the man page)
* Programmer Port
-
-P /dev/ttyUSB1
- the most likely for my systems
* Part Identifier
-
-p m168
- for use with an ATMega168 -
-p m328p
- for use with an ATMega328p -
-p m1280
- for use with an ATMega1280
* Burn Counter
Not technically required, but a good idea. The burn counter is stored in the last 4 bytes of eeprom
-
-y
- to increment the burn counter each burn -
-Y value
- to initialise the burn counter
Baud Rate
Required for stk500v1
-
-b 57600
- for most of mine
Terminal Mode
-
-t
- see #terminal_mode for mode
Memory Access
There are others, but these are the most common
-
-U flash:operation:filename[:format]
- where the firmware lives -
-U eeprom:operation:filename[:format]
- non-volatile memory -
-U lfuse:operation:filename[:format]
- low fuse byte -
-U hfuse:operation:filename[:format]
- high fuse byte -
-U efuse:operation:filename[:format]
- extended fuse byte
operation
can be:
-
r
- read -
w
- write -
v
- verify
filename
points to the file to use
format
can be:
-
a
or omitted - for auto-detection -
i
- Intel Hex (output from obj-dump) -
r
- Raw binary - other (see the man page)
Terminal Mode Commands
dump
-
dump memtype address nBytes
- dump nBytes from address in hex and ASCII -
dump
- continue for another nBytes
write
-
write memtype address byte1 ... byteN
- write to memory by hand, currently doesn't work with flash :(
parm
-
part
- display information on the connected part